Harris DC Power Cable, Pt # 10570-0705-A021, 20 Ft, New. NSN 5995-01-681-7499. 4 Pin Connector with 3 conductors. Pin A is Black wire about 12 ga; Pin B is Red wire about 12 ga, Pin C is Brown wire about 20 ga, Pin D not used. The cable may have an additional conductor that I cannot see because of shrink tubing on end and I have not taken the connector apart. Powered by SixBit’s eCommerce Solution
Looking for an easy way to pull your civilian 12v trailer behind your 24v military truck without splicing wires? You have found the solution. These are built to order and typically take a week to build. As a result, your tracking number will take approx a week to post after purchasing so please be patient! Onto the Features Proudly Made in the USA • 12 Volts @ 20 Amps (240 watts lighting power) • Surge Suppression • Overload Protection • Automatic Reset • Water-proof • Plug & Play (no wire cutting or splicing) Compatibility • 3 Lever or Push Button Light Switch • “Service Drive” and “Park” modes How It Works Takes power from the tail light circuit, wire #21, and converts it to 12 volts. That 12 volt power is fed into relays that are triggered by wires# 22-460 and 22-461, the left and right stop/turn circuits. The 12 volts from the power converter and relays are fed to a civilian trailer connector. The tractor versions have additional relays that provide separate turn and stop lighting circuits for semi trailers. A note about power The adapter will supply a total of 20 amps (240 watts) for trailer lighting. The standard 12 volt 1157 taillight bulb draws 26 watts for stop/turn and 8 watts for tail. A typical trailer setup of two stop/turn/tail light bulbs (one per side) with running lights on and brakes applied will use 68 watts, leaving 172 watts for marker lights (they tend to be 8 watts or less, so at least enough power for 20 of them). Or a ridiculous number of LED lamps. A load of greater than 240 watts will overload the converter and cause it to shutdown. The converter will auto-reset once the overload is cleared. This particular auction is for a 7 way RV & 4 way flat connector on trailer end. 12 Pin nato for truck end. We have multiple options- 7 way J560 semi trailer, etc. Call us with Q Jim 5076762972 to ensure we get you the correct convertor for you application. This is a plug and play box that plugs into your military trailer plug. You then will plug your trailer wiring harness plug into the convertor box for easy 12v trailer lighting. Made in USA. 12volt at 20 amps (240 watts lighting power) , surge protection, automatic reset and waterproof. Works with both the traditional 3 way light switch and also the push button light switch. 7 way RV style trailer connector. Cable that plugs into military light receptacle is nato style 12 pin and is 6ft long. If you need specialized trailer converters, have questions or need Parts please give us a call. Tracking will take approx a week to post after purchase due to custom build process so please be patient. Shipping price listed is for continental US only. If for export please email us for shipping quote.
Features • 12 Volts @ 20 Amps (240 watts lighting power) • Surge Suppression • Overload Protection • Automatic Reset • Water-proof • Plug & Play (no wire cutting or splicing) Compatibility • 3 Lever or Push Button Light Switch • “Service Drive” and “Park” modes How It Works Takes power from the tail light circuit, wire #21, and converts it to 12 volts. That 12 volt power is fed into relays that are triggered by wires# 22-460 and 22-461, the left and right stop/turn circuits. The 12 volts from the power converter and relays are fed to a civilian trailer connector. The tractor versions have additional relays that provide separate turn and stop lighting circuits for semi trailers. A note about power The adapter will supply a total of 20 amps (240 watts) for trailer lighting. The standard 12 volt 1157 taillight bulb draws 26 watts for stop/turn and 8 watts for tail. A typical trailer setup of two stop/turn/tail light bulbs (one per side) with running lights on and brakes applied will use 68 watts, leaving 172 watts for marker lights (they tend to be 8 watts or less, so at least enough power for 20 of them). Or a ridiculous number of LED lamps. A load of greater than 240 watts will overload the converter and cause it to shutdown. The converter will auto-reset once the overload is cleared. Detail of Standard Versions Standard Converter Cable The Standard Converter Cable has a 7-Way RV style trailer connector mounted in a waterproof box and a 6’ 12 pin NATO style cable that plugs directly into any standard military truck’s trailer socket. ALL COMPANY NAMES & PRODUCT’S ARE TRADEMARKS™ OR REGISTERED® TRADEMARKS OF THEIR RESPECTIVE HOLDERS. USE OF THEM DOES NOT IMPLY ANY AFFILIATION WITH OR ENDORSEMENT BY THEM IN ANY SHAPE OR FORM.HUMMER® AND H1® ARE A REGISTERED TRADEMARK OF GENERAL MOTORSMIDWEST MILITARY EQUIPMENT’S SERVICES & ALL OF IT’S PRODUCTS ARE NOT AFFILIATED WITH AM GENERAL LLC. HUMVEE®, HMMWV® AND THE HUMVEE VEHICLE CONFIGURATION ARE REGISTERED TRADEMARKS™ OF AM GENERAL LLC. Midwest Military Equipment is not the manufacturer of any vehicle, and any “builds” described by Midwest Military Equipment consist of custom mechanical and artistic modifications and repairs to existing vehicles performed by MIDWEST MILITARY EQUIPMENT which are not endorsed, authorized, affiliated sponsored or approved with the manufacturer of said vehicle in any way.
